<<O>>  Difference Topic SiliconTrackerDaugtherBoard (r1.4 - 07 Jun 2013 - AlvaroDosil)

META TOPICPARENT Documentation

Silicon Tracker Daughter Board

Changed:
<
<
In order to allow the readout of a silicon strip module assembled with a Tracker Turicensis hybrid (4 Beetle chips) with the Alibava system (2 Beetles), a daugther board STDB and a adaptor board STDBAdaptor has been developed.
>
>
In order to allow the readout of a silicon strip module assembled with a Tracker Turicensis hybrid (4 Beetle chips) with the Alibava system (2 Beetles), a daugther board STDB and a adaptor board STDBAdaptor has been developed. It is very important to note that the TT hybrid uses Beetles version 1.3.

The STDB adapt the 34-pin IDE alibava connector to the 80-pin AVX TTHybrid connector, manual selection of 2 over 4 beetles and allow external beetle i2c programming.

 <<O>>  Difference Topic SiliconTrackerDaugtherBoard (r1.3 - 04 Jun 2013 - AlvaroDosil)
Changed:
<
<
META TOPICPARENT WebHome
You are on TWiki.Instrumentation. (PabloVazquez - 19 Jul 2011)
>
>
META TOPICPARENT Documentation

Silicon Tracker Daughter Board


In order to allow the readout of a silicon strip module assembled with a Tracker Turicensis hybrid (4 Beetle chips) with the Alibava system (2 Beetles), a daugther board STDB and a adaptor board STDBAdaptor has been developed.

The STDB adapt the 34-pin IDE alibava connector to the 80-pin AVX TTHybrid connector, manual selection of 2 over 4 beetles and allow external beetle i2c programming.

Added:
>
>
Alibava setup

Added:
>
>
Alibava’s software and hardware are designed to work with two Beetles. As we use a TT-hybrid with 4, we need a way to select the pair of Beetles that we will read. We have to choose the firmware, namely 0x10-0x12.mcs and 0x14-0x16.mcs, and then accordingly set the switches in the STDB. There are leds near to the switches to show which address we are selecting. Although each switch has 6 different selectors, all must be switched together. There is a red button with a red led, which allow us to cut the Beetle’s power.

The STDB provides a 4-pins port where we plug the I2C bus from Arduino board, or the oscilloscope. Below a screenshot of a reset command sent to Beetle 0x16 from Arduino.

Alibava setup


META FILEATTACHMENT DB_ST_Esperante_v2.zip attr="" comment="" date="1303207772" moveby="PabloVazquez" movedto="Instrumentation.SiliconTrackerDaugtherBoard" movedwhen="1311067388" movefrom="Instrumentation.WebHome" path="DB_ST_Esperante_v2.zip" size="2087585" user="DanielEsperante" version="1.2"
META FILEATTACHMENT STDBAdapter.rar attr="" comment="" date="1311151066" path="STDBAdapter.rar" size="52714" user="PabloVazquez" version="1.1"
Added:
>
>
META FILEATTACHMENT STDB.png attr="" comment="Silicon Tracker Daughter Board" date="1370362105" path="STDB.png" size="781681" user="AlvaroDosil" version="1.1"
META FILEATTACHMENT image04.png attr="" comment="Reset command sent to Beetle 0x16 from Arduino" date="1370363577" path="image04.png" size="54962" user="AlvaroDosil" version="1.1"
 <<O>>  Difference Topic SiliconTrackerDaugtherBoard (r1.2 - 20 Jul 2011 - PabloVazquez)

META TOPICPARENT WebHome
Changed:
<
<
-- PabloVazquez - 19 Jul 2011
>
>
You are on TWiki.Instrumentation. (PabloVazquez - 19 Jul 2011)

In order to allow the readout of a silicon strip module assembled with a Tracker Turicensis hybrid (4 Beetle chips) with the Alibava system (2 Beetles), a daugther board STDB and a adaptor board STDBAdaptor has been developed.

The STDB adapt the 34-pin IDE alibava connector to the 80-pin AVX TTHybrid connector, manual selection of 2 over 4 beetles and allow external beetle i2c programming.


Deleted:
<
<
In order to allow the readout of a silicon strip module assembled with a Tracker Turicensis hybrid (4 Beetle chips) with the Alibava system (2 Beetles), a new daugther board STDB has been developed.

Deleted:
<
<
The board is basically: a connector adaptor, it allows to select 2 over 4 beetles and external i2c programming

META FILEATTACHMENT DB_ST_Esperante_v2.zip attr="" comment="" date="1303207772" moveby="PabloVazquez" movedto="Instrumentation.SiliconTrackerDaugtherBoard" movedwhen="1311067388" movefrom="Instrumentation.WebHome" path="DB_ST_Esperante_v2.zip" size="2087585" user="DanielEsperante" version="1.2"
Added:
>
>
META FILEATTACHMENT STDBAdapter.rar attr="" comment="" date="1311151066" path="STDBAdapter.rar" size="52714" user="PabloVazquez" version="1.1"
 <<O>>  Difference Topic SiliconTrackerDaugtherBoard (r1.1 - 19 Jul 2011 - PabloVazquez)
Line: 1 to 1
Added:
>
>
META TOPICPARENT WebHome
-- PabloVazquez - 19 Jul 2011

In order to allow the readout of a silicon strip module assembled with a Tracker Turicensis hybrid (4 Beetle chips) with the Alibava system (2 Beetles), a new daugther board STDB has been developed.

The board is basically: a connector adaptor, it allows to select 2 over 4 beetles and external i2c programming

META FILEATTACHMENT DB_ST_Esperante_v2.zip attr="" comment="" date="1303207772" moveby="PabloVazquez" movedto="Instrumentation.SiliconTrackerDaugtherBoard" movedwhen="1311067388" movefrom="Instrumentation.WebHome" path="DB_ST_Esperante_v2.zip" size="2087585" user="DanielEsperante" version="1.2"
View topic | Diffs | r1.4 | > | r1.3 | > | r1.2 | More
Revision r1.1 - 19 Jul 2011 - 09:26 - PabloVazquez
Revision r1.4 - 07 Jun 2013 - 15:30 - AlvaroDosil